Copper Gutter Brackets

/Copper Gutter Brackets

HRC Copper Gutter Brackets part 2

HRC Copper Gutter Brackets. This is the second 100 for the job that has now turned into 300. So one more round to go. Customer requested an additional 7/8″ to be added to the part that grabs the rafter to get the gutter to ideal drip line position. You will notice in some pictures that there is a back tab that is partially bent. We recommend placing a piece of the gutter into the bracket and starting that fold. Sometimes (depending on elevation) that tab can be a tad bit difficult to fold as it may be almost touching the […]

By |2021-02-25T21:23:12+00:00February 25th, 2021|Copper Gutter Brackets|0 Comments

HRC Copper Gutter Brackets

HRC Copper Gutter Brackets. This is the first 100 of 200 for the job. Customer requested an additional 7/8″ to be added to the part that grabs the rafter to get the gutter to ideal drip line position. You will notice in some pictures that there is a back tab that is partially bent. We recommend placing a piece of the gutter into the bracket and starting that fold. Sometimes (depending on elevation) that tab can be a tad bit difficult to fold as it may be almost touching the underside of the roof deck. Ya can’t get your fingers […]

By |2021-02-25T21:18:42+00:00February 16th, 2021|Copper Gutter Brackets|0 Comments

HRCDT Custom Copper Gutter Brackets

HRCDT Custom Copper Gutter Brackets. These were custom made to fit a Rafter Angle that could not be determined. We sent a sample to the customer with his best guess. He sent it back after he “tweaked”. You can see the tweaked bracket in some of the pictures…
We have made over 1000 Gutter Brackets for this project. Same with Downspout Brackets. Have a couple more years to go on it.

By |2021-01-17T15:48:40+00:00January 17th, 2021|Copper Gutter Brackets|0 Comments

Commander 6K Gutter Brackets for 6″ K-Style Copper Gutters

Commander 6K Gutter Brackets for 6″ K-Style Copper Gutters. This is the Roof Hanger portion plus one complete assembly. That assembly is important to help establish the Projection of the Roof Hanger for optimal position. This is a large order – 220 – Bracket Assemblies. Contractor wants to get the Roof on so we did the Roof Mounts first and the balance of the order will process shortly. The actual Gutters won’t go on for some time…

By |2020-11-08T21:09:00+00:00November 8th, 2020|Copper Gutter Brackets|0 Comments

SideRider Copper Gutter Brackets Hangers

SideRider Copper Gutter Brackets Hangers. This was a little tricky as customer wanted an extra long mounting arm. So a little tougher to bend etc.
There are Lefts and Rights for two different roof pitches. 9/12 and 10/12. So packaging we will have to keep things grouped so no mistakes or Easter egg hunt.
We have marked for each type the MASTER. The master is used to compare and then tweak each bracket so it matches the master for each style. They must not only match pitch but when put on their sides be perfectly flat.

By |2020-11-01T11:23:58+00:00November 1st, 2020|Copper Gutter Brackets|0 Comments

HRC Double Tab Copper Gutter Brackets

HRC Double Tab Copper Gutter Brackets. This was tricky. They have to mount to a 2″ by 4″ fascia. Not a lot of room to account for slope. These brackets are for a good customer who has purchased 1000’s of brackets. You will notice in a few pictures a “Chamfer Bit”. We are supplying this bit to him so if he needs it to do some more chamfering he can do it more easily. Chamfering holes removes material and that hole at the top rear of the bracket has to accept a #12 Screw. We pushed the limit to what […]

By |2020-10-24T13:45:53+00:00October 24th, 2020|Copper Gutter Brackets|0 Comments